CipherLab 1266 Especificaciones Pagina 159
- Pagina / 180
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
147
Update
Chapter 6
Applying Formats for Data Editin
g
6.6.2 EXAMPLE II
Extract the date code, item number, and quantity information from barcodes.
Data in a barcode is encoded like this:
From the 1
st
character to the 6
th
character is the date code.
From the 7
th
character to the dash ‘-’ character is the item number.
After the dash ‘-’ character is the quantity information.
Data will be transmitted like this:
The item number goes first, then a TAB character, followed by the date code, then another TAB
character, and finally the quantity information.
The editing format should be configured as follows:
1. Read the “Enter Setup” barcode to enter the Configuration Mode.
2. Read the “Configure Format 2” barcode.
3. Read the “Three Fields” barcode.
4. Read the “Divide Field 1 by Length” barcode, and set length to 6.
Field 1 data starts from the 1
st
character to the 6
th
character.
5. Read the “Select Field Separator to Divide Field 2” barcode, and use a dash ‘-’ character.
Field 2 data starts from the 7
th
character until the dash ‘-’ character is met.
6. Read the “Additional Field 1” barcode, and use a tab character for the field.
7. Read the “Start (Programming)” barcode to program the transmission sequence.
8. Read the “Field 2”, “Additional Field 1”, “Field 1”, “Additional Field 1”, “Field 3” barcodes.
9. Read the “End” barcode to complete the transmission sequence (F2 A1 F1 A1 F3) setting.
10. Read the “End Programming Format” barcode to complete the setting of Editing Format 1.
11. Read the “Enable Format 2” barcode to apply Editing Format 2 to all code types.
12. Read the “Update” barcode to exit the Configuration Mode.
- 1166 / 1266 Barcode Scanne 1
- IMPORTANT NOTICES 3
- RELEASE NOTES 5
- CONTENTS 7
- INTRODUCTION 13
- SETTING UP 3666 15
- DIRECT CHARGING 16
- Introduction 17
- SYMBOLOGIES SUPPORTED 18
- QUICK START 21
- ENTER CONFIGURATION MODE 23
- EXIT CONFIGURATION MODE 23
- DEFAULT SETTINGS 24
- RESTORE SYSTEM DEFAULTS 24
- Quick Start 25
- Refer to Appendix III 28
- LIST THE CURRENT SETTINGS 29
- Chapter 1 31
- 1.2 MEMORY 33
- 1.2.1 TRANSMIT BUFFER 33
- 1.2.2 MEMORY MODE 34
- Chapter 1 35
- 1.4.1 GOOD READ BEEP 38
- 1.4.2 FREQUENCY 38
- 1.5 SCAN MODES 39
- 1.6 SCANNING TIMEOUT 43
- Laser mode 43
- Auto Off mode 43
- Auto Power Off mode 43
- 1.9 NEGATIVE BARCODES 46
- Chapter 2 47
- 2.1 BT HID 48
- 2.1.2 RESET CONNECTION 49
- Chapter 2 51
- Selecting Output Interface 51
- 2.2 BT SPP SLAVE 58
- 2.3 KEYBOARD WEDGE VIA 3666 59
- Keyboard Wedge via 3666 60
- No. Keyboard Type No 60
- Keyboard Type 60
- 2.3.2 KEYBOARD SETTINGS 61
- US Keyboard Style – Normal 62
- 62
- Cap Lock Type Description 64
- Alphabets Transmission 66
- ALT Composing 68
- Laptop Support 68
- 2.3.3 INTER-CHARACTER DELAY 69
- 2.4 RS-232 VIA 3666 70
- 2.4.2 BAUD RATE 70
- 2.4.3 DATA BITS 71
- 2.4.4 PARITY 71
- 2.4.5 FLOW CONTROL 72
- 2.4.6 INTER-CHARACTER DELAY 72
- Chapter 3 73
- Set Connection 74
- 3.1.2 CHANGE INTERFACE 75
- Sniff Mode (Power-saving) 76
- 3.2 CONNECTING VIA BLUETOOTH 77
- 3.2.1 CHANGE INTERFACE 77
- Chapter 3 79
- 3.2.3 CONNECT TO DONGLE 81
- Chapter 4 89
- 4.1 CODABAR 90
- 4.1.3 CLSI CONVERSION 91
- 4.2 CODE 25 – INDUSTRIAL 25 92
- 4.2.2 VERIFY CHECK DIGIT 93
- 4.2.3 TRANSMIT CHECK DIGIT 93
- 4.3 CODE 25 – INTERLEAVED 25 95
- 4.3.2 VERIFY CHECK DIGIT 96
- 4.3.3 TRANSMIT CHECK DIGIT 96
- 4.4 CODE 25 – MATRIX 25 98
- 4.4.2 VERIFY CHECK DIGIT 99
- 4.4.3 TRANSMIT CHECK DIGIT 99
- 4.5 CODE 39 101
- 4.5.2 VERIFY CHECK DIGIT 102
- 4.5.3 TRANSMIT CHECK DIGIT 102
- 4.6 CODE 93 103
- 4.7 CODE 128 103
- 4.8 EAN-8 104
- 4.8.1 CONVERT TO EAN-13 105
- 4.8.2 TRANSMIT CHECK DIGIT 105
- 4.9 EAN-13 106
- 4.9.1 ISBN CONVERSION 107
- 4.9.2 CONVERT TO ISSN 107
- 4.9.3 TRANSMIT CHECK DIGIT 107
- 4.10 GS1-128 (EAN-128) 108
- 4.10.1 TRANSMIT CODE ID 108
- 4.11 MSI 109
- 4.11.1 VERIFY CHECK DIGIT 109
- 4.11.2 TRANSMIT CHECK DIGIT 109
- 4.12 FRENCH PHARMACODE 111
- 4.12.1 TRANSMIT CHECK DIGIT 111
- 4.13 ITALIAN PHARMACODE 112
- 4.13.1 TRANSMIT CHECK DIGIT 112
- 4.14 PLESSEY 113
- 4.14.1 CONVERT TO UK PLESSEY 113
- 4.14.2 TRANSMIT CHECK DIGIT 113
- Chapter 4 115
- Changing Symbology Settings 115
- Transmit Check Digit 116
- GS1 DataBar Expanded 117
- Transmit Code ID 118
- Transmit Application ID 118
- 4.16 TELEPEN 119
- 4.17 UPC-A 120
- 4.17.1 CONVERT TO EAN-13 121
- 4.17.3 TRANSMIT CHECK DIGIT 121
- 4.18 UPC-E 122
- 4.18.4 TRANSMIT CHECK DIGIT 124
- Chapter 5 125
- Chapter 5 127
- Defining Output Format 127
- 5.3.2 CHANGE CODE ID 130
- 5.3.3 CLEAR CODE ID SETTINGS 131
- 5.4 LENGTH CODE 132
- Chapter 6 137
- 6.1.2 EXCLUSIVE DATA EDITING 139
- End Programming Format 140
- 6.2.2 RESTORE DEFAULT FORMAT 142
- 6.3.1 APPLICABLE CODE TYPE 143
- 6.3.2 DATA LENGTH 147
- 137 149
- 6.4.2 FIELD SETTINGS 150
- 143 155
- Additional Fields 155
- Key Type Key Status 155
- 145 157
- 6.6 PROGRAMMING EXAMPLES 158
- 6.6.1 EXAMPLE I 158
- 147 159
- SPECIFICATIONS 161
- Appendix I 163
- Click [OK] 164
- USING BLUETOOTH 165
- DONGLE 165
- HOW TO UPGRADE 3666 FIRMWARE 167
- Appendix I Firmware Upgrade 169
- Enter Setup 170
- SN: SW3000014 170
- Appendix II 171
- EXAMPLE 172
- Appendix III 173
- KEY TYPE & STATUS 174
- KEY TYPE 174
- KEY STATUS 174
- Appendix IV 177
- HEXADECIMAL SYSTEM 178
- ASCII TABLE 179
- USE PRESET PIN 180
- DISABLE AUTHENTICATION 180
Relacionado con productos y manuales para Lectores De Códigos De Barras CipherLab 1266
(160 paginas)
(277 paginas)Lowrance electronic GPS receiver user manuals
Starting on L
© 2020, manymanuals.es. Todos los derechos reservados | 0.087 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales