CipherLab 1266 Manual de usuario descargar pdf (Pagina 11)

1515

5. Bluetooth Serial Port

The 1166/1266 can be configured to the standard Bluetooth Serial Port as the data

output interface. This will make the 1166/1266 send the scanned barcode data to

Bluetooth enabled computer or PDA directly without the 3666 base unit (however,

a charging dock is still needed for charging the 1166/1266 battery).

This section illustrates a step-by-step installation and configuration procedures of

the 1166/1266 for Bluetooth Serial Port. Bluetooth transceivers/dongles always

come with their own driver or Windows XP with service pack2 provides the build-

in Bluetooth driver. There are several Bluetooth device drivers for Windows and

WinCE/Pocket PC from different companies. Here we use Window XP with service

pack2 build-in Bluetooth driver and BELKIN driver as examples. For detail

installation procedures, please refer to the user’s manual of the Bluetooth

transceiver in use.

5.1 Configuring 1166/1266

Before starting the configuration, the scanner must be powered up. If you have not

done so, please follow the procedures described in section 2.2 “Power Up the

1166/1266” to power up the scanner.

First step of the configuration is always to put the scanner in configuration mode by

scanning the “Enter Setup” barcode. After all the desired configurations are done,

the “Update” barcode must be scanned to save the new settings and put the scanner

back to normal operation mode.

5.1.1 Activate Bluetooth Serial Port Interface

Scan the “Activate Bluetooth Serial Port” barcode will change the interface type to

Bluetooth Serial Port.

5.1.2 Authentication & PIN Code

The 1166/1266 can do connection authentication if communication security is

desired. Once this setting is enabled, a user configurable PIN code is verified during

connection establishment. The scanner will refuse connection if the PIN code is

incorrect. User can specify up to six characters of PIN code.

5.1.3 Device Name Broadcasting

The scanner can be configured to hide itself by NOT broadcasting itself on the air.

This can avoid unwanted computer/PDA from connecting to the scanner. But for

the initial (first time) connection setup, this setting must be enabled. User can

disable this setting for security reasons after initial connection setup is completed.

5.1.4 Update Settings

After all the desired settings are completed, the “Update” barcode must be scanned

to make the new settings effective. The scanner will re-start itself after “Update”

barcode is scanned.

5.1.5 Timeout

The scanner will stay active only for one minute waiting for connection. If there is

no connection request during that period, the scanner will go to power down mode

to conserve power with three serial descending tones as indication. User can make

the scanner go back to active mode by pulling the trigger. And again, the scanner

will stay active for another one minute waiting for connection before it goes to

power down mode again. Once there is a successful connection, the scanner will

stay active until the connection is closed (when the host application closes the

COM port). After the connection is closed, the scanner will again wait for new

connection request for one minute before it goes to power down mode.

5.2 Configuring Bluetooth Device Driver

Please follow the procedures below to configure the Bluetooth driver on the host

system. Please note that, when searching nearby Bluetooth devices on Host

computers, the 1166/1266 will come out with the serial number as their device

name. Please check the serial number label on the scanner when making

connections.

5.2.1 Windows XP with Service Pack2

1. Insert the Bluetooth dongle into PC host.

2. Double click the Bluetooth icon on the lower right of the taskbar.

1 2 ... 6 7 8 9 10 11 12 13 14 15 16 ... 54 55

Comentarios a estos manuales

Sin comentarios

CipherLab 1266 Manual de usuario Pagina 11

Comentarios a estos manuales

Relacionado con productos y manuales para Lectores De Códigos De Barras CipherLab 1266