CipherLab 1266 Manual de usuario Pagina 14
- Pagina / 55
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
21
2121
21
8. Click OK button.
After successful connection, the Bluetooth Device Driver will report the COM
port number, which is mapped for this connection. In this case, it is COM3.
You can also hear three serial ascending tones from the scanner indicating
successful connection.
After this initial connection, whenever an application program opens COM3,
the Bluetooth driver will automatically try to connect this particular scanner.
9. Right click the COM1 and select Disconnect to close the connection. There will
be three serial descending tones from the scanner to indicate this condition.
After the connection is closed, the 1x66 scanner and the Bluetooth driver are
properly configured and are ready to go. User can now run their application or
“Hyper Terminal” for testing, and make the best use of this scanner.
22
6. Bluetooth HID
The 1x66 scanner can be configured to the standard Bluetooth HID as data output
interface. This will make the 1x66 scanner sends the scanned barcode data to
Bluetooth enabled computer or PDA directly without the 3666 base unit (however,
a charging dock is still needed for charging the 1x66 battery).
This section illustrates a step-by-step installation and configuration procedures of
the 1x66 for Bluetooth HID. Bluetooth transceivers/dongles always come with their
own driver or Windows XP with service pack2 provides the build-in Bluetooth
driver. There are several Bluetooth device drivers for Windows and WinCE/Pocket
PC from different companies. Here we use Window XP with service pack2 build-in
Bluetooth driver and WIDCOMM driver as examples. For detail installation
procedures, please refer to the user’s manual of the Bluetooth transceiver in use.
NOTE: Bluetooth HID doesn’t support the following functions on PDA:
Capital Lock Setting: Auto Detection
Digit Transmission: Numeric Key
Alt Composing
6.1 Configuring 1166/1266
Before starting the configuration, the scanner must be powered up. If you have not
done so, please follow the procedures described in section 2.2 “Power Up the
1166/1266” to power up the scanner.
First step of the configuration is always to put the scanner in configuration mode by
scanning the “Enter Setup” barcode. After all the desired configurations are done,
the “Update” barcode must be scanned to save the new settings and put the scanner
back to normal operation mode.
6.1.1 Activate Bluetooth HID Interface
The HID keyboard interface is enabled by configuring/selecting the HID keyboard
type. The supported HID keyboard types are listed below: US, French German,
Italian, Swedish, Norwegian, UK, Belgium, Spanish, and Portuguese KBD.
6.1.2 Reset Connection
Scan the “Reset Connection” when switch connection from one PC to another PC.
The scanner will re-start itself after this barcode is read.
- User’s Manual 1
- Table of Contents 2
- 1. Introduction 4
- 2. 3666 Installation 5
- 2.4 Charging your 1166/1266 6
- 2.5 Interface Setting 6
- 3. General Features 7
- 3.5 Re-read Delay 8
- 3.7 Reading Redundancy 8
- 3.8 Supported Symbologies 8
- 3.9 Negative Barcodes 8
- 4.2 RS232 Interface 10
- 4.3 USB Interface 10
- 4.4 Memory Parameters 10
- 5. Bluetooth Serial Port 11
- 6. Bluetooth HID 14
- Keyboard 15
- 7. Symbology Parameters 18
- 7.10 Plessey 20
- 7.11 Telepen 20
- 7.12 RSS 20
- 8. Data Output Format 21
- 9. Data Editing 22
- 10.2 Default 24
- 10.3 List Setting 24
- Parameter Label 25
- Key Type / Status Label 25
- Two Hexadecimal Labels 25
- "Validate" Label 25
- Revision History 27
- • Memory Mode 28
- • Clear Data 28
- • Send Data 28
- • Memory Data Delay 28
- List Setting 29
- Buzzer Settings 29
- Reading Redundancy Setting 29
- Scan Mode Setting 29
- Auto-Sense Setting 29
- Scanner Time-out Duration 30
- Negative Barcode Setting 30
- Delay between Reread 30
- Keyboard Wedge Parameters 30
- RS-232 Parameters 32
- Bluetooth HID Parameters 33
- Prefix / Postfix Settings 35
- Character Substitution 35
- Code ID Selection 35
- Code ID Setting 35
- Select Readable Codes 37
- Code39 Parameters 40
- Italy Pharmacode Parameters 40
- French Pharmacode Parameters 40
- Industrial 25 Parameters 40
- Interleave 25 Parameters 41
- Matrix 25 Parameters 42
- Codabar Parameters 42
- Plessey Parameters 43
- Telepen Parameters 43
- MSI Parameters 43
- EAN128 Parameters 44
- EAN8 Parameters 44
- UPCA Parameters 44
- UPCE Parameters 45
- EAN13 Parameters 45
- RSS Code ID Selection 46
- RSS14 Parameters 46
- RSS Limited Parameters 46
- RSS Expanded Parameters 46
- Activate Editing Formats 47
- Editing Format Parameters 47
- • Applicable Data Length 48
- • Total Number of Fields 48
- • Applicable Code Type 49
- • Field1 Setting 50
- • Field2 Setting 50
- • Field3 Setting 51
- • Field4 Setting 51
- • Field5 Setting 52
- • Additional Fields Setting 52
- Decimal Digits 53
- Hexadecimal Digits 54
- Key Type 54
- Key Status 54
- KBD Wedge Character Table 55
- RS-232 Character Table 55
Relacionado con productos y manuales para Lectores De Códigos De Barras CipherLab 1266
(4 paginas)
(277 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.034 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales